No. 169: Best Train Wrecks of 2021

Reflecting on 2021

Post-Christmas is a great time for reflection and planning for the new year. I always like to make plans for the next year after Christmas. I think it’s a good way to set goals and “refresh” myself for the year ahead.

In my hobby life, it’s a good time to reflect on my wins and losses for the year, and make renewed plans for the new year. I think I had some good hobby wins—I finished a lot of projects and the Hermitage Road layout is now about 90% complete. But I had a whole lot of less-publicized losses which also need to be recorded—in other words, my best train wrecks for the year.

Best Train Wrecks of 2021

Like the photo above, train wrecks are best shared with other people.

This Milwaukee Road car was finished in March. I’ve been trying to slowly add some 50-foot cars to the fleet to add some variety. I took a lot of time to get the build right, and get the paint color right, and get all the details right. After laying the decals down, I hit it with Dullcote. Then I noticed that there were some prominent bubbles in the Route of the Hiawathas decal. See them all trying to hide on top of that rib? If I try to fix it I’ll ruin the rest of the finish. So I’ll just have to face that car away from the aisle forever.

Doesn’t that make you wonder why we finish both sides of a model in the first place?

This is a Monon single-sheathed Fowler box car that I bought from Chad Boas at St. Louis RPM 2017. I decided that I wanted to build new ends, so I cut the model up and added new ends and a replacement Westerfield roof. Well, one thing led to another and I tore up everything to the point where I had to consign this one to the round file. I’ll try again…this time with an Accurail car.

Here’s an NP Historical Society War Emergency box car, finished a year or two ago. The decals cost twenty bucks (!!!) and were beyond thick. Thick decals for a single-sheathed car are a bad combination. They went on terribly and I worked on them for weeks. I‘m mentioning this one because this year I discovered Walthers Solvaset, which is much more powerful than MicroScale Decal Set, and I think had I used Walthers Solvaset on this car I would’ve had much better results.

Turning Cars White

I got really good at turning finished models white this year. Really good. It happens when applying Testors Dullcote to a finished model to seal the decals and paint. There are a lot of theories why this happens; in my experience, it occurs when the atmospheric humidity is greater than 40-50%, and also sometimes when the mixture is wrong (Dullcote + thinner) and sometimes when the atmospheric temperature is doing something stupid (too cold, or too hot, with perhaps some extra moisture in the air). It also happens if the coat goes on too thick, or if there is latent humidity on the model. Sometimes I think it is caused when the Dullcote dries in the air, after it leaves the airbrush on the way to the model.

Check out this New York Central hopper. It was formerly an M&StL car that I sandblasted, rebuilt and repainted with new K4 decals. The Dullcote pooled in the corners and turned a nice snowy white.

I was able to remove most of the coating by painting the model with paint thinner once or twice and thinning the dry Dullcote. Then I weathered the car a little heavily to fix the problem areas. I didn’t intend to heavily weather the car, but to avoid yet another trip to the sandblaster I weathered it hard and put it away wet. Results are okay (seen below).

I rebuilt this Wabash car in August while the family was away in the US for a few weeks. I painted it with Tru Color Wabash Freight Car Red and used the new K4 Wabash decal set to finish it. The model is an old Sunshine mini-kit. Well, wouldn’t ya know—after I hit it with Dullcote and it turned white. The picture doesn’t show it too well, but when it dried it looked like it was frozen.

In my anger I didn’t take a picture of its snowy whiteness. Instead, I brought it to the workbench and painted it with paint thinner to reduce the Dullote, and that worked somewhat. Once again, I had to heavily weather it, but I found that was a little prototypical since these cars were rebuilt in 1940 and by 1950 they were trashed.

Here’s the over-weathered version. I think another repaint is in this car’s future…

Here’s a hard-to-find Sunshine Rock Island rebuilt flat car that I bought on eBay a few years ago. I built, painted and decaled it, then turned it almost completely white with a bad shot of Dullcote. I sandblasted it, and found a set of decals from Hubert Mask that would work. So I re-painted and re-decaled the model…then turned it completely white again. A few paint-thinner baths and some touch up later, here’s the result. What a mess.

This CB&Q 50-footer, which I carefully built and added all kinds of things to, including a lot of expensive Archer rivets. To improve my chances I tried using Mr. Hobby flat finish. Test shots went on great. Yet somehow I managed to turn this model almost completely white as well. It’s now completely stripped and ready for a second try.

Below. All those expensive rivets…and decals…have been blasted away after I turned the whole bloody thing white.

And this Sunshine Models Milwaukee single-sheathed box car? The first paint job I put the wrong number series on the car. I robbed the decals from another Sunshine kit and repainted it, but it turned out so bad that I couldn’t live with it. The third time—using K4 decals—was a charm. There’s a more details discussion on the repainting at https://railroadprototypemodeler.wordpress.com/2021/11/20/no-172-completing-the-traverse-table-and-milwaukee-road-single-sheathed-box-car-re-do/.

Third times a charm:

Without a doubt the biggest train wreck of the year was this MP car. I spent about eight hours rebuilding this thing. Everything went well, including the paint, decals and Dullcote. When it was done, I looked closely…and found out that I put two different numbers on the car. One side is 86147 (correct) and the other side is 89147 (incorrect). Holy crap.

Best Layout Wrecks of 2021

I managed to pack a lot of wrecks into my 7’ x 18” layout this year. For example:

I built the coal yard, then took it apart and re-laid the track, then rebuilt the coal yard again…twice.

I rebuilt the grocery warehouse three times, as I outlined in my last blog post.

I built—to a level of 99% completion—the Alcatraz Paint & Varnish Co. Then I removed it and replaced it with the Sitterding, Carneal & Davis Mfg Co. (both were prototypes served by the SAL). I built two versions of Sitterding, and am modifying version two already.

Here’s Alcatraz, below. It’s gone.

The team track loading ramp didn’t escape either. I laid it down, moved it and destroyed it, then rebuilt it, and moved it again. Twice.

Here’s the team track ramp below. In the background are several other versions of other factories that I tried for a few weeks. They’re gone too.

Lessons Learned

1 – Do it right the first time!
2 – My actual hands-on hobby time is limited to about five or six hours a week. Rounding up, that’s about 300 hours a year. Note: Last year I spent probably 150 hours fixing mistakes.
3 – See #1.

There’s a footnote too: NEVER, EVER freelance a layout.

2022 Plans

I’m facing a move from Germany to the US in 2022. I’m also facing a career change. That’ll shake up my life and the first thing to go will be all my hobby time.

That means my hobby time will be even more precious. So I’ve really got to slow down and do things right the first time so I can finish 2022 with more wins, zero losses, and zero ties.

Hope you guys had a better year than I did! – John G

No. 168: Hermitage Road Layout – Modeling the Grocery Warehouse

On my little Hermitage Road switching layout, I wanted to include a grocery warehouse to generate refrigerator car traffic on the small layout.

There were a few grocery warehouses in the Hermitage Yard area that were rail-served through the 1950s so I felt it would be okay to include one on the layout. While studying Sanborn maps, I didn’t find any in the immediate area on the Seaboard, but I found several in the Richmond area on the ACL and C&O lines.

This photo, below, provided some inspiration for my model. I understand this one was in Dallas, Texas.

When I planned the layout last year I felt a grocery warehouse could work on either end of the layout. I wanted the track in front at the edge of the layout, with a larger building immediately behind it, to 1) Get the cars as close as possible to the operator, and 2) allow the track to run into the fascia to create a feeling that the track continues well beyond the fascia.

Below, here is the layout under construction last year with a box serving as a stand in for the grocery warehouse. You can see how I’ve got the track running in the foreground but behind the fascia.

Before I built the layout, I built up one of those Walthers Reliable Warehouse models for fun. The build was straightforward. I painted the model with Tamiya Flat Brown, XF-10 and used Tru Color Concrete on the foundation and Testors Guards Red on the windows. During construction I used Robert’s Brick Mortar on the model and it went on very well and the results were excellent.

Here’s a view, below, of how I wanted the building and track to be in the foreground with the track running behind behind the fascia.

I completed the model before I built the layout, and arranged the track around it, but it never quite worked out right. After a short while I replaced it with a larger structure made from Walthers Cornerstone Modulars, seen below. The Modulars building was way too big, and I felt it overpowered that side of the layout. So I removed that one and set it aside too.

Then I built a third version using parts left over from the Marshall Canning Company structure on my old Ackley, Iowa layout. I added a photo of that one below. I built several increasingly smaller versions. I was not able to get the mortar between the bricks to my satisfaction so I scuttled that project.

Frustrated, I went back to the original reliable warehouse building. I tore it apart, rebuilt it to fit the space, and here’s the result. Putty has been applied to a few gaps leftover after I deconstructed it and put it back together.

I scratchbuilt the elevator machinery house and the staircase on top using leftover material, and the chimneys are metal castings from various kits collected over the decades. I also built gutters from styrene strip and made lamp-posts from Tichy lampshades. I’m VERY happy with the final version.


Above and Below. Details for the grocery warehouse.

Here’s the final version, installed on the layout and 99% complete. About the only thing left to do is to weather the tarpaper roof somehow (it is black construction paper). That can wait a while though.

And there you have it–many versions of the same building, but finally we have one we can keep!

Rock Island 133000-series Box Car

Here’s a freight car project I’ve been working on for a few months. This is a Rock Island 133000-series single-sheathed box car that I built from parts from various Westerfield kits. I contacted Andrew Dahm at Westerfield and asked him about the car, and between us we figured out which parts might work to kitbash the car from Westerfield parts. He sent me a box full of kits and I got to work.

In the meantime, I contacted Mike at K4 decals and asked him if he could make up a decal set for this car and a few other Rock Island single sheathed cars. I also got in touch with Steve Hile, an RPM friend of mine and a Rock Island expert, and together we put together a data package for Mike. Steve did 99% of the research work. Mike had the decals ready in less than a week. In fact, I already have two sets here in Germany.

Here’s the link to the decals: Rock Island 40 Ft Single Sheathed Boxcar White – Decal – Choose Scale – K4 Decals – Model Train Decals.

My model is built, sandblasted and ready for paint. I’ll send a complete post on the model in a while after it’s finished.

I hope you all had a wonderful Christmas celebration and I wish you blessings for 2022! – John G

No. 167: Completing the Traverse Table, and Milwaukee Road Single-Sheathed Box Car Re-Do

I had minor arthroscopic knee surgery last Wednesday and took a few days off from work to recover. I was able to make some good progress on the layout during those days. Here’s an update.

Traverse Table

Here’s what the small, 7 x 18-inch Hermitage Road layout looks like today. At the far end, the dark square box is the entrance to the staging area.

Below. Here’s the other side of the portal to staging. There wasn’t enough room for a traditional staging yard with all the turnout ladders and all that, so I built a British-style traverse table instead.

A traverse table is a yard without the turnouts. The advantage is that it saves a lot of space in a given area. My design has a single entry track from the layout, a five-track “table”, and two exit or runaround tracks at the opposite end. The table is secured to the layout with a single screw underneath the center of the table. Each yard track holds 5-6 cars plus an engine. I used Atlas Code 83 track because I had it on hand.

In this photo, the traverse table tracks are mocked-up to see what’ll fit. The drawer slides are underneath the table, and extend out behind the table to allow the table to slide across all five tracks in either direction.

Below. After the table was built and aligned, I was able to lay track. First, the roadbed must be placed. Getting everything straight and lined up as perfect as possible is important since the all the tracks need to line up on each end of the table. After gluing the roadbed down I used switch locks to hold it in place.

Below. I laid the roadbed at the entrance end first. Then one-half of the roadbed was laid using a straight-edge. Before going any further, I waited a day and allowed the glue to dry, and then glued down the other half of the roadbed.

Below. In this photo, roadbed for three tracks has been laid. Using the 90-degree angle tool and the long straight-edge kept everything in proper alignment.

Below. All the tracks have to be spaced exactly the same so they will line up with the end extensions.

After all the track was laid, I wired up the table. Wiring was simple. I had to wire the front and end extensions, and each track, and that was it. I wired all the tracks together into a bundle and left enough slack in the bundle to allow the table to move. The track wires have quick connections so I can disconnect the table in just a minute if needed.

Below. Work in progress. What a mess!

Below. One of my daughters came upstairs to give me a hard time.

The layout is now operational again, thanks to the Mr. Traverse Table. Below, you can see that the engine is powered up and we’re hard at work moving coal cars through the portal to Hermitage Coal Co.

If you look closely at the bottom of the photo you can see that the height of the table doesn’t quite match up with the end. See the difference in track height? That’s something that needs adjusting soon.

Milwaukee Road 713471…or is it 714142?

You may remember this car from a previous post. It is an old Sunshine Models car that I finished about a year ago. I used the salt weathering technique on the roof, but in this case was never quite satisfied with the look.


Above. In August, during my “16 Days” building bonanza, I stripped the paint on this model and started over. First I sandblasted the model and then repainted it with Tru Color TCP-213 Milwaukee Road 1930-50’s Freight Car Brown. I decaled the car with K4 decals’ Milwaukee Road Single Sheathed Boxcar set.

The weather here in Germany was nice in September so I set up a table in the garage and did a lot of painting out there. Unfortunately, when I shot Testors Dullcote on the roof of this car, the finish turned white.

Below. Time for damage control. I gave the roof a bath with paint thinner and that took off most of the white residue. Then I weathered the roof with various AIM weathering powders, like Soot Black, Weathered Brown, and Oxide. I mised a new batch of Dullcote and sealed the powder.
A couple of weeks ago, Charlie Duckworth posted on one of the Groups.io lists and showed a few new cars he’d built. One or two of them had really nicely-weathered running boards. He used darker gray colors–darker than I normally use–and they looked great. I mixed up a palette of grays, and mixed in some earth tone paint color, and used used various shades on this car. I think it turned out well. Contrast is the key!

Finally, a last overhead view. I think the weathered running board turned out well against the darker roof.


What’s In The Box?

I got a mystery box in the mail last week with my long-awaited Rapido PRR X31-class box cars!

The cars look terrific and they are a great improvement over the Bower models, which–despite the molded-on stuff–I always thought looked great too. I got one of each for now because I need to save my sheckles for X-3s, GLas, an SP single-sheathed car, and whatever else they can surprise us with.

The Pros, in my opinion: Overall appearance, color, lettering, brake gear, details like grabs, etc. The Cons: Trucks (they’re awful!), brake wheel, coupler box/draft gear (why can’t we have something with some detail???), #5 couplers. There’s also no bell crank on the B end, but I’ll have to research that to see what equipment the real cars had. As for replacement trucks, Bowser has a nice pair of PRR-specific coil-elliptical trucks that can be used to improve the models.

Below. Here’s a closeup of the B end on the auto car. It looks terrific. The PRRT&HS had a lot of say in the development of this model, in particular the paint color, and I trust their judgement.

May God richly bless you and your families during Thanksgiving. Don’t forget to give thanks! – John

No. 166: Modeling Rock Island Steel Box Cars

In August, during the “16 Days” work campaign, I began a project to rebuild and repaint a dozen or more freight car models.

Two of those models were Rock Island favorites. The first was an Intermountain 1937 Modified AAR car that needed to be stripped and repainted because I did a poor job of decaling and finishing the first time around. The second was a Sunshine Models USRA rebuild that I finished 15 years ago or so, which needed updating. I just finished those models last week Here’s the report, with a little history.

RI 146309

Rock Island rostered over 4,100 1937 AAR Modified box cars. They were delivered with a variety of different doors and features, and some were outfitted with Duryea underframes. Some cars were built as express cars and were delivered with Allied full-cushion trucks. Refer to Ed Hawkins’ car rosters for detail on each series.

Below. I’ve built a number of models of these cars over the years. Here’s one of the first I built, photographed in 2001 in my back yard when I lived in California. There were fewer aftermarket parts back then, but still I installed the wrong type of grabs, and for some reasons painted those old fat-wheel Kadee trucks black. Those are Champion decals too.

Below. I took this photo in 2004 after living in Illinois a year. RI 146756 was yet another car for the roster, but my technology had not improved. In the background is yet another Rock Island car.

Below. I finished this car, RI 146301, in 2007. Better trucks and somewhat improved brake gear (as far as I can tell from here…), but I was still using Champ decals, and still no leap in finishing.

Below. RI 147313 shows some improvement. I finished this model around 2013. This model has Tahoe trucks and semi-scale wheelsets, better decals (a combination of Hubert Mask and Champ), and much-improved brake gear modeling. This was also the first model that I applied Kadee grabs to.

I covered the Salt Weathering technique in a previous post, which can be found at https://railroadprototypemodeler.wordpress.com/wp-admin/post.php?post=9909&action=edit.

Turn the page six years. Let’s try again, this time with a now-hard-to-find undecorated Intermountain kit. I get rid of many of the parts–the trucks, running boards, grabs and the details and replace them all with better products. It’s about time for a 21st Century model of this car, isn’t it?

The latest model was assembled with Cal Scale brake gear and a ton of aftermarket parts all around. I installed the grabs using the Yarmouth Models template, taped to the car and then drilled through. I fixed the grabs with canopy glue. Getting the grabs on the ends lined up is NOT easy, but worth the time spent. I’ve run out of Jim King’s draft gear boxes and used Kadee #178 coupler boxes—not a bad compromise. So far, the build is pretty good and a trip through the sandblaster will clean up most of the mess and prep the slippery Kadee plastic for paint.

As I mentioned above, I finished the model about six months ago, but the paint and finish was poor so I immediately stripped it and repainted it. Here’s why: I used K4 decals for this model; when they arrived in the mail they were wet. I attempted to use them on this car and they did not go on well. I continued to finish the car and the results were not what I hoped for, so back in the sandblaster it went. Here’s the new model ready for paint…again…

And here we are after painting. I’m using Tru Color RI Freight Car Red, TCP-197 Rock Island 1930-60’s Freight Car Brown, thinned about 30% with Lacquer Thinner. Again, a technological leap over Scalecoat, in my opinion, with the added advantage that Tru Color is dry and ready for decals in 60 minutes.

I made my own running boards for this car using plastic strip. I should’ve taken more care to leave some space between the boards on the latitudinal.

Mike at K4 Decals was kind enough to send me replacement decals without charge. He sent the decals in plastic sleeves, but the sleeves weren’t sealed shut and somewhere in the trip to Europe they collected a little moisture. The replacement decals came in a box with sealed plastic and were perfect.

I’ve found that K4 decals are somewhat thicker than Speedwitch or Microscale decals. Microscale Decal Set and Testors Decal set had little effect on them. I tried a stronger setting solution—Walters Decal Set—and that worked great to get the decals to settle around rivets and detail. It’s pretty strong stuff and usually worked well in just one application.

Ultimately I plan to model two of these cars. This one, from the 146000-series without a Duryea underframe, and a second car from the 148550-149049 series with a Duryea underframe. George Toman displayed some inspirational work on the Resin Car Works blog modeling one of the cars with the National Scale Car Duryea underframe set, and I want to copy his effort soon on the second car. George’s article can be found at http://blog.resincarworks.com/workbench-wednesday-26/#more-2733.

Here’s my car, about 99% finished:

Back on the rails she goes!

RI 134541

RI 134541 is the other car I recently rebuilt. This is an old Sunshine Models car I’ve had around for about 15 years. It’s a cool model of a cool prototype, and even though Sunshine Models is gone you can get a kit from Chad Boas and make your own.

Rock Island rebuilt 800 USRA double-sheathed box cars to this configuration beginning in 1936. C&NW rebuilt over 1,200 of thier USRA double-sheathed cars similarly. A spotting feature of both car types is the original USRA 5-5-5 end with a blank panel added in the middle to increase the height of the end. There’s excellent coverage of these cars in RP Cyc #24.

Here’s a Jim Sands photo of a Rock Island car, circa 1960, courtesy Clark Propst.

Here’s my starting point for the rebuild, below. The photo is circa 2008. Why rebuild it? The model is the wrong color, and I got some silvering behind the decals that I could never fix.

First things first. A trip through the sandblaster cleaned off the weathering, all of the Dullcote, and prepped the surface for new paint. A little more pressure took the decals off.

Details used on the model include A-Line stirrups, Tichy 18-inch drop grabs, Hi-Tech air hoses with brass brackets, Tahoe Model Works 40-ton trucks with semi-scale wheelsets, and a Cal Scale brake gear set.

I thought the original build was pretty good, so I went ahead and painted the car without any detail upgrades. Here’s the model repainted with Tru Color TCP-197 again, which as you can see is a lovely, light maroon color.

Decaling was straightforward. I used the same K4 Rock Island box car set for this model, but I had to cut out the numbers to get the right number combination. I also had a leftover Rock Island decal set that came with the original kit I built all those years ago, and used the 80,000 lb. CAPY decals to get it right. Once again I used Walthers Decal Set because it works great with K4 decals.

I referred the prototype photo above for placement of the monogram. Note the monogram is NOT centered within the right side panels.

After decaling the model I hit it with a few light coats of Dullcoat and a few light coats of Testors Light Earth for weathering. I really didn’t want to over-do the weathering on this car.

Below. A closer-up view of the B end. The blank panel in the end is well-represented.

Here’s the finished model, below, on the layout and ready for action. I made the photo black-and-white to add a little period effect.

Hope you all have a great week! – John G

No. 163: 16 Days, Pt. 4

The 16 Days program ended last Monday when my wife and daughters returned from their U.S. trip.

In those 16 days I was able to complete major work on several structures for the layout, rebuild and repaint a dozen freight cars, complete construction on one new freight car, and paint the traverse table for the layout. I also sold five models on eBay and in other places, and I also spent a considerable amount of time writing on this blog.

I normally try to keep the layout and workbench very clean and organized, but during the 16 Days I allowed myself to leave everything a hot mess so I could go right upstairs and pick up where I left off.

I originally estimated that I could accomplish 73 hours of work during the 16 Days. I was only able to complete about 36 hours of hobby work, however. I underestimated the time needed for my day job, chores, yard work, daily exercise, a few parties/get-togethers, and other things that took away my time.

The significant layout project was finishing the traverse table. I was able to disassemble, paint, and reassemble the traverser but that was it. It was a hot day, and my house doesn’t have air conditioning, and the third floor train room got really hot. I didn’t get too much done that weekend. There’s a lot of work to be done still.

On the layout, among the projects I wanted to complete while the family was away was painting the fencing for the Hermitage Coal Co. and building, painting and applying mortar to the grocery warehouse.

The fencing is made by Tichy and comes in six-inch sections. The fencing took a few hours to assemble and paint, then it was painted with Tamiya Medium Brown. Then I painted a few of the individual boards with various shades of tan, gray and dark brown. Next I applied a thinner-and-black-paint wash to get black paint into the crevices and the board detail. Finally, I gave it a light coat of Medium Brown again to blend everything together, then sprayed it one more time with Testors dullcote to finish the job.

Before installing the fence I need to do a little scenery repair, and also shorten the coal company track about four inches.

The grocery warehouse is coming along. Below, I have applied some Roberts Brick Mortar and am letting it dry. At this point, I’m not too happy with this model. It’s gonna need a lot of work…

Below. The grocery warehouse after mortar removal. I still don’t like it, but I’ll keep working on it and give it a chance.

Fortunately I was able to get some big freight car work done during the 16 Days. I was able to check a dozen models for operation (checking coupler height, cleaning wheels, minor repairs, etc.)–something that I don’t do very often.

Here’s one car, below, that got some much-needed attention. This is of course a Proto 2000 model, and my records indicate I’ve had it since 2003. I’ve upgraded the tracks and a few details since then, and I’m still very happy with the paint and weathering. It’s a keeper.

Below. I have been unhappy with this car for a long time. This is a Tichy rebuilt box car with a Sunshine mini-kit applied. I finished this car in 2008; the photo below dates from 2013. I have never been happy with the color, and the Wabash lettering on the right side of the car “silvered” for some reason–on both sides too.

Last week I sandblasted the decals and weathering off and then fixed a few original construction problems, like the placement of the grabs on the corners, and I also replaced the door tracks.

Below, after sandblasting I added a replacement door track and also the missing sill brackets.

I also removed and replaced the grabs on each corner to line them up prototypically. I’ve repainted the car with Tru Color #191 Wabash Freight Car Red and have new K4 Decals ready to go. That coupler pocket is ghastly!

Another car I was unhappy with was my Sunshine Models Illinois Terminal single-sheathed box car. This is a cool car, and at 37 feet long it stands out in a crowd. But, I just wasn’t happy with the color and weathering. Here’s a photo of that car I took on my old Ackley layout:

I sandblasted the lettering and paint off the car, replaced a few details, and repainted it last week. Here’s how it looks today. I’ll be using Resin Car Works decals to re-letter the car.

Here are a few more cars that I rebuilt and repainted.

I sold my Tichy B&O USRA SS Box Car online last week and am preparing a replacement, below.

Why get rid of a good car and replace it with another? I spent the time to put the side grabs in the right place and install additional rivet detail using Archer rivets. The grabs line up properly, and are in the right place (the car kit suggests they should be further toward the center of the car; proto photos indicate otherwise) and I also added Archer rivets below the NBW castings. Unfortunately the Archer rivets have disappeared.

For some reason, I didn’t use the awesome Tichy running board. I replaced it with styrene strip. I think the styrene strip running board looke=s great, as seen below, but it is missing the great Tichy bolt detail.

I’ll be using Speedwitch/National Scale Car decals for the car above. The car below is a Sunshine Rock Island rebuilt USRA double-sheathed car that also was rebuilt and repainted. Apparently I forgot to paint the trucks at the same time…

A shout out to my buddy Jim Dufour, who finished a similar car recently and sent a photo to a chat group I participate in. C&NW had prototype conversions similar to the Rock Island cars, and Chad Boas makes kits for both of them. Jim used the Chad Boas kit for his model, below, and did a superb job with it. The weathering is perfect. Love that Viking roof too!

Yet another Rock Island car is below. This is a 50-foot rebuilt flat car, another Sunshine Models kit, with Tahoe Model Works Dalman trucks. It’s hard to see but this is the car with the big splice panels on the side. Unfortunately the kit didn’t come with decals, but Clark Propst showed me a Hubert Mask set that should work.

Below. Here’s the new build I finished during the 16 Days. This is a CB&Q 50-foot Box Car from the Proto 2000 kit. Next: Sandblasting (again), then a coat of paint, then a lot of extra rivets, then a final shot of paint before decals. I’ll be using the awesome Speedwitch/National Scale Car decal set for this car too.

The CB&Q XM-28 is alas another Sunshine kit that got new paint and decals a few months ago. Last week I weathered it, applied some chalk marks with a white Prismacolor pencil, cleaned up the wheel treads, and got it ready for service. The car look alright and is ready for the layout.

So that’s it–the 16 Days came and went. I got a lot done but still have a long way to go. Priorities for the rest of the calendar year are finishing the layout, and finishing all these cars, and getting another engine or two detailed up.

See ya next time! – John G

No. 162: 16 Days, Pt. 3

Work on the railroad continues as the family is traveling in the U.S. for two weeks.

One of the industries I built this week for my Hermitage Road switching layout as a “grocery warehouse”. In the area of Richmond, Virginia, where my layout is set, there were quite a few grocery warehouses, and I wanted to include one on the layout so I could use refrigerator cars. There are no known photographs of the grocery warehouses in the Hermitage Yard area so I was forced to proto-freelance something.

On my old Ackley, Iowa layout I built a large cannery as seen in the photo below. This week I took the building out of storage and took it apart, cleaned and repainted everything, and then reconfigured the walls into a much smaller building that fits in the corner of the new layout.

Below. A view of the Marshall Canning on my Ackley Layout. The building was 36-inches long.

Below. The new grocery warehouse on the Hermitage Road layout. On the right side of the layout, the track runs behind the building; I intend to build a loading dock that extends past the end of the building on the left. The windows are ready to go–all I need is time to paint and weather the building.

Here are the old doors and windows from Marshall Canning. The windows and personnel doors are from Tichy, and the loading dock doors are scratchbuilt using scribed styrene and strip styrene. I think the building will look nice with a medium-brown brick with red trim. The large Sitterding mill behind the grocery warehouse will have green trim to keep all the buildings from looking alike.

Below. Believe it or not, I have already built two grocery warehouse models for the Hermitage Road layout. Here’s the first one I built, using a Walthers Cornerstone building I had on hand. On this side of the layout, the track runs in front of the building to simulate that it continues to other industries. This structure was built to fit behind the track. With the track in front, I get to enjoy seeing my freight cars a little more.

I used Robert’s Brick Mortar on the building and I think it came out really nice. Alas, I thought this building was too tall, and took over the scene, so it has been removed and is stored away. The Southern Fuel and Oil Co. will go in this spot instead.

This spring I built a second grocery warehouse using Walthers Modulars. This version was only two stories tall so it was less imposing, but after I completed it, I felt it was too big and too deep. It just didn’t scratch the itch. I wanted to use Walthers Modulars for the Sitterding building, so I dismantled this one and have reassembled in into the current Sitterding building which was shown in the last post.

The Southern Fuel and Oil Co. will go in this spot instead.

Meanwhile, work continues on freight cars. These are two favorites, below, but I haven’t used them on the layout yet because I was unhappy with my roof weathering efforts. The model on the left is an Intermountain 1937 Modified car, and the model on the right is an Intermountain “War Emergency” box car. Both these models were built and painted about 6-7 years ago.

Below. Here are the roofs. When I built these models, my research indicated that Viking roofs on CMO and C&NW cars were galvanized with paint on the seams caps. I painted the roofs on both cars like the one on top; with silver, and black or red seam caps.

Why didn’t I like these roofs? In the first place, galvanized metal doesn’t really look silver. It’s more gray, so I wasn’t happy with the finish. In the second place, I recently talked to Ed Hawkins and he said that ACF documents indicate that roofs on both of these cars were painted the same color as the carbody. Below, I’ve sandblasted one of the roofs and will blast the other this weekend, and repaint them soon. The roof on top, incidentally, has a Kadee running board and the roof on bottom has a Plano metal running board.

Y’know…after sandblasting…the one of the bottom looks pretty good just like it is, doesn’t it?

While I was sandblasting, I put an old Kadee hopper in the booth and blasted the paint off it as well. Earlier this week I ordered a Missouri Pacific detail set from Resin Car Works, and I’ll use that to rebuild and repaint this car. I will model one of the MoPac cars with the horizontal seam on the sides.

From the Resin Car Works site, below. The model I’m interested in is on the right:

The link for the MoPac decal and detail set can be found at http://resincarworks.com/decals_parts.htm.

Also in progress is this new build, a CB&Q 50-foot steel box car using the Proto 2000 model. I got a couple of kits from my friend Greg Silva. I’m using a printout from a Ted Culotta presentation to help me get the details right.

Car construction consumed a couple of evenings this week. One of the hardest jobs was installing Kadee bracket grab irons on the car sides. I used the template from Yarmouth Model Works. Getting the template in the right place isn’t easy. Once the template is in place, I drill the holes and then remove the template. Then I have to enlarge the holes to fit the mounting tabs on the back of the grabs. I use canopy glue to affix the parts, and when it’s dry I go over the whole area with Tamiya liquid cement to melt everything together. Then I sandblast it so the Kadee parts will accept paint. It’s a lot of work but the parts look great.

Here’s the workbench during construction of the new Q car. I cut out all the parts, and build the subassemblies, and then assemble the car when all the subcomponents are ready. There’s a whole lot of after-market parts on this table–from Yarmouth, Hi-Tech, Detail Associates, Cal Scale…the list goes on. No wonder I don’t have any money!

You can see another car there on the right. That’s an Intermountain 1937 Modified car kit that I’m finishing right behind the Q car. That’s Missouri Pacific 1937 Modified car and I’m using the awesome National Car Company mini-kit for that build. I’ll talk about it next time…

The last thing I did this week was swap components from two Kato engines to convert my Milwaukee Road DC RSC-2 to sound/DCC.

I took apart my NYC RS-2, equipped with a SoundTraxx sound/DCC setup, swapped the trucks, and married the sound/DCC underframe with the RSC-2. I felt kinda like Dr. Frankenstein doing this–taking an engine without a brain and swapping it for one with a brain.

Here are the victims in the lab. Body parts all over the place!

After an hours’ worth of work, I had a sound/DCC-equipped RSC-2. I still have some work to do on the cab–it needs a crew and open windows, and I also need to replace a few grabs and lift rings.

The next night I put the NYC RS-2 back together and sold it on eBay for cheap. No need to keep too much stuff around the house.

Work continues this weekend, as I paint freight cars, finish the traverse table, and continue structure work. Only 36 hours are left…gotta work hard tonight! – John G

No. 161: 16 Days, Part 2

Work continues while the family is away!

When I last showed the Richmond Cinder Block Company, it needed windows. The windows I used, seen below, are from Tichy. I painted them with a Tamiya Metal Gray and then added clear styrene sheet windows and fixed them with canopy glue. Once the glue was dry I then sprayed the whole assembly front and back with full strength Dullcote. I painted in a few window panes white to simulate broken glass repair.

Next I added the windows to the structure, gluing them in place from behind with Tamiya extra thick liquid solvent. I randomly left a few windows open and closed to add a little interest. Next: Paint the sand bin and the mechanical buildings, paint the stack, and add some detail to the conveyor. I also bought a few packages of Funaro & Camerlengo cinder blocks and will put them around the open doors. I guess I’ll need to weather the track appropriately too.

To the right of the cinder block plant is the large Sitterding-Carneal-Davis Construction Company mill. I’m using Walthers Modulars for my building; the real one didn’t look much like this as far as I know. I’ll write much more on Sitterding this week as I get going full-speed on construction.

Speaking of new tools…

I’ve been using a small, battery-operated Dremel tool for precision drilling for over ten years. The problem is it spins too fast—5,000 rpm minimum—and that’s too fast for drilling plastic and resin. It never spun quite true either. I’ve been looking at cheap Chinese drills on Amazon for a long while, and back in June I just bought one. Here’s the one I got:

This drill was imported by ____. It has a U.S. plug and runs on 110 volts, and includes a little speed adjustment rheostat. The whole outfit was 35 bucks. The drill is big, and heavier than I expected, but it’s solid. I’ve been using it all week and it’s working great. The rheostat works great and I can dial the rpm to match the material. It is super-quiet too. Most importantly, the thing spins true-to-center—NO wobble. It works great with .078 bits. I highly recommend it. If you buy one, tell China I sent you.

Below. Back to freight cars. Here’s a project I’ve been putting off for years. Around 2009 I built and painted this Atlas 1932 ARA car for an SCL Modeler article. In the original article I assessed the model as excellent, but I wrote that the doors were “horrible”.

Not long after that article was published online, Ted Culotta at Speedwitch introduced a beautiful set of doors to upgrade the Atlas model. I bought a set in 2014 but never took the time to install them…until now.

I began the upgrade by removing the Atlas doors, which was a lot more complicated than I expected. I had to pry the original doors off in pieces and then trim down the press-fit tabs on the car sides so the new doors would fit. Worse, the Atlas door includes door-opening hardware that would be normally be attached to the car side. So I had to trim the door-opening hardware off the Atlas door and secure it to the Speedwitch door to retain all the appropriate detail.

See the photo below–the door on the left came straight off the car. The door at the center has had the detail strip removed off the left side of the door. The Speedwitch replacement door is at the right, with the detail strip added.

Below. A close-up view. I carefully removed the door-opening strip from the Atlas door and then glued it to the Speedwitch door using Tamiya liquid cement. After everything was dry I sanded around completed door casting to make sure everything was square.

To make things even more fun…the Speedwitch door is shorter in height than the Atlas door. That meant I had to adjust the position of the bottom door track to make the door fit. I removed the original bottom door track and replaced it with a piece of Evergreen styrene, filled the attachment holes for the original door track, and then hand-painted all the new parts on the car. The doors will be airbrushed later this week.

I added a few more parts to the SAL car, like new uncoupling devices (Tichy .0125 brass wire), new stirrups (from Yarmouth), and tack boards from National Scale Car Co. I used Atlas ARA truck previously, but I ordered a pair of Tahoe Model Works Buckeye as they are close to the prototype and the level of detail is much better than the Atlas trucks.

I may have mentioned that I traded Tangent Scale Models 40 bucks for a bunch of spare parts. Here are the parts bags I got. They’re quite nice and everything is easy-to-glue plastic, not the slippery, impossible-to-glue acetyl stuff that Kadee uses.

Here’s one of the new brake wheel housings, added to that Sunshine Rock Island single-sheathed box car I mentioned last time. Looks good!

And finally, I finished and sent Eric Reinert’s last car to him. This was a pretty standard build, only I took the time to add rivets on the side panels per the prototype. I used Archer rivets and they practically disappeared after paint and lettering and weathering. In this view, before Dullcote and weathering, the added row of rivets can be seen on the right side of the car.

After Dullcote and a month’s-worth of weathering, here’s the final version I sent to Eric. I think I over-did it and I wasn’t happy with the final product, but Eric e-mailed and said he was delighted. I added just about all the modern features to this car–Yarmouth sill steps, Tahoe trucks with semi-scale wheelsets, Hi-Tech air hoses (which are getting awfully hard to find) and plenty of wire details all around. I used the Speedwitch detail set of course. Roof weathering was done with AIM powders.

Tonight I got to work on two new builds–a CB&Q 50-foot steel box car (Proto 2000)–inspired by a Ted Culotta lecture–and a MoPac 1937 Modified box car using the National Scale Car parts. More to follow next time.

John G

No. 160: 16 Days, Part 1

At the beginning of August, my family traveled away and left me at home alone for a while. After a very busy and very social summer, and a summer full of travel, I have the first 16 days of August to myself to catch up on some modeling work. This is the first of hopefully several posts on what’s happening during these 16 days.

Below. Last week I took my son to Radovljica, near Lake Bled, and spent three days with him hiking and swimming. We hiked to this mountain hut at the foot of Mt. Triglev, which is seen in the background. Triglev is only 9,300 feet but the climb is very difficult with a lot of Via Ferrata near the top. He and some friends will climb Triglev later this week.

Before I get to this week’s modeling work I’d like to commend Lonnie Bathurst, Jeff Kuebler and the St. Louis RPM team for a fantastic meet in Collinsville, Illinois last weekend. 750 modelers and historians attended, breaking all of our previous attendance records. I helped, spending five or six months soliciting vendors and historical societies, gathering and organizing clinicians, and laying out the room arrangement. Lonnie and Jeff in particular did the lion’s share of the work organizing and making sure everything went great on “Game Day” as we call it. The meet went well and I think the record attendance was partly because we went to great lengths to host a live event and didn’t let anybody’s covid fears wreck the party.

Here’s a photo of last week’s fun from Ron Christensen.

I wasn’t there to take photos but hopefully Lonnie and the team will post photos soon. Our official Flickr photo site is at St. Louis Railroad Prototype Modelers’s albums | Flickr and you can find photos of all our other events there. Meanwhile, Eric Hansmann has started a thread on the Model Railroad Hobbyist forum to encourage sharing of images. A few have appeared and maybe more will post today. That site is at https://model-railroad-hobbyist.com/node/43187.

Meanwhile, here in Germany, the short list of work for “16 Days” includes finishing structures for the Hermitage Road layout, working on and finishing locomotives and freight cars, and finishing and fitting the traversing table so operations can resume.

Among the structures I’m working on this week is the Richmond Cinder Block Co., which was located behind the SAL’s Hermitage Yard in North Richmond. I don’t have any prototype photos of the plant, but I do have a Sanborn image as seen below. I wanted to model Richmond Cinder Block because of the variety of inbound loads a cinder block plant can generate, among them hoppers and gondolas with sand, covered hoppers with cement, and box cars for both inbound and outbound loads.

Sorry for the fuzzy image!

Here was my first rendition, below. I started building the model before the track was even put down on the layout. I used Pikestuff block for the bins at the left, but used Plastruct cinder block sheet, which is very thin, on the main building instead.

The building above just didn’t scratch the itch. First, the plastruct material was entirely too thin, and required a lot of styrene reinforcement. Second, I got to thinking that a cinder block company really doesn’t ship out too many loads of completed blocks. More research confirmed this–most cinder block manufacturers ship locally, so a plant like this wouldn’t necessarily generate a lot of outbound box car loads.

At the beginning of summer I decided to rebuild the plant, based more on the drawing and less on how many box cars I can jam on the little layout. I bought more Pikestuff block sheets and finally this week I was able to get to work.

I cut up the remaining parts of the original plant and repositioned the parts in various configurations to see what “looked right”. Below, things are taking shape. The Hermitage Coal Co. is at the front.

Here’s where we were on the first evening of the 16 Days. I decided to adjust the roof lines and the front faces of the building (actually the rear) to create some more visual interest and also try to replicate the Sanborn drawing to some extent. Eliminating the long, flat side of the building went a long way to providing some depth to the overall structure. Also adding a few things on top to give the model some height, and break up the roof line, helped add some realism as well.

Here’s where we are at the end of this morning’s building rush. I added roofs (again, using different roof lines), windows, doors, and other details. Adding the roofs took a long time and consumed a whole lot of styrene sheet. I didn’t notice until I finished this morning’s building that I installed some of the windows upside down. What a dope!

The thing on the left is a sand pit. No, the original drawing doesn’t include this, but I wanted to add something to hold additional sand or cinders–sort of an overflow facility like some coal docks used to have. I built a conveyor leading up to the two bins. The two buildings at the end are machine sheds or garages that face away from the track.

I built the bin using first by constructing a simple plastic box, then sheating it with HO scale 2×8 styrene shapes from Evergreen. That’ll give it a plank-by-plank look, and later I can accentuate the planks with a little contrasting paint.

You wouldn’t believe how much time this building has consumed in the last couple of days. Probably 12 to 15 hours…

I made the silos by covering a cardboard tube with 3M heavy-duty double-sided tape, and then wrapping the thin Plastruct siding around it. My inspiration came from a photo of a ready-mix plant in Mason City, Iowa, sent to me by Clark Propst. Below you can see the photo, the cardboard tube–an empty tape roller–and the tape.

I wrapped the tube in the tape, then cut a piece of block sheet to fit…


…and then carefully wrapped the plastic sheet around the tube. The process took about 20 minutes to complete both silos.

I’ll get more done on the cinder block plant this week, but now I want to concentrate on freight car work. Below is shown an old Sunshine Models Illinois Terminal box car that needs a repaint. I repaired some damage to the roof and rebuilt it with a few new parts (air hoses, changes to the brake gear, repairs to the running board and latitudinals, repairs to the brake platform and step on the B end, and a few other things). The major problem is I will need decals of the monogram and don’t think anyone makes them in HO. Still gotta do some research before I blast the paint off.

This old dog got some attention too. This is a Sunshine Models FGE car I’ve had around for 15-20 years. The light is poor but the car got new Tahoe Model Works trucks, some underframe upgrades, sill step repair, and Hi Tech air hoses. This Old Dog–a tip of the hat to Mac Demarco, one of my kid’s favorite “indie rock” singers. Mac’s got some good stuff!

Below. Here’s another old dog that got some TLC last night. This is a Proto 2000 car that got Hi Tech air hoses, cleaned-up wheel tread, weathering on the running boards, and…yeah, I think that’s all it got. I finished this car in the mid-2000s and at that time used my sandblaster to lightly blast off some lettering on the car side in an attempt to create a fading effect. This is a cool prototype and a favorite car, as it stands out nicely among all of it’s box car red bretheren.

Check out that new background. Did you notice that the windows are all fixed now?

Also in progress this week is rebuilding/repainting of this Rock Island car. It is yet another Sunshine Models car–a rebuilt Rock Island USRA box car. When I originally finished it about 15 years ago I painted it a really dark brown. RI freight car color is more maroon than brown, so I bought new decals from K4 and will refinish this car as soon as I can check out all the detail parts and make sure everything’s ready for paint.

I love the prototype RI cars as shown above. Luckily for us, we can still get these kits even though Sunshine Models is gone. Chad Boas sells parts to built the RI and similar C&NW cars.

Below. Here’s a portrait I took of the same car in 2009:

Why the rush to repaint this car? I’m repainting this RI 1937 Modified car, below, so I thought I’d repaint them both at the same time. I painted the car below and used some faulty K4 decals (they somehow got a little wet in the mail, but I used them anyway). I got a new set from K4 a few months ago, so I blasted the decals off this one and will repaint and them at the same time.

That covers all the hard work in the first three of 16 days. Next, more HO and Proto48 freight car work, a whole lot of painting, and on the weekend if all goes well I’m going to get to work finishing up the travering table for the layout.

Hope you have a wonderful week! – John G

No. 158: O Scale Work, and Central of Georgia Auto Car

I took a few days off of work before Memorial Day and went on three day-trips with the family over a five-day period. The most interesting was a road trip to Belgium and Luxembourg with my son to buy beer.

My son and I went to a neat place in Arlon, Belgium called Mi Ougemi Houblon to buy a variety of craft beers.  It was a cool store and a lot of fun, and the guy working there was very friendly.  We drove to a Del Hayes grocery next to buy a stroop waffles and more beer–this time the easy-to-get stuff from the larger Belgian breweries. Later we went to the Orlan Monastery, where they also happen to make a famous beer called Orlan. We took a tour of the old churches and of course bought some of their rare and excellent brew.

Below. Here’s a view of one of the many shelves at Mi Ougemi Houblan:

My son is an architecture student and during the day we stopped at various towns and small cities to look at the church architecture. Now that my son has some training he was able to explain all the architectural features in some detail. For a 19-year-old his teaching ability is impressive. He would start with the big picture, explaining the type, look and feel of each structure–and we saw many of them. Then he would get into the details. “This is early Gothic, and this is why…”. The Orlan Monestery was Roman architecture and he explained all the difference there too. He would explain how certain features were weight-bearing, and how they became decorative, and how they were used, and what certain features meant, and so on.

Below, and difficult to photograph, is the fantastic Gothic cathedral in Orlan, Belgium.

I could go on…and on…but I won’t. It was a memorable day with my good son.

O Scale Work

Last year I attempted to repair two brass hoppers in my very small O scale collection. Both cars had minor damage and I made things worse trying to fix them. An RPM friend–Brian Strom–came to my rescue. I sent him the cars and he repaired them for me. Not only did Brian repair the cars but he cleaned them up and repainted them perfectly as well. He did an exceptional job.

Here’s a before-and-after picture of the first car, a 35-year-old Precision Scale PRR hopper car that I bought from Jim Canter. My work is on the left, and Brian’s repair work is on the right. Note that he also over-did it, and painted the coupler pocket and weathered up the coupler. RPM friends are really the best friends!

Here’s the completed model at Brian’s shop.

Brian also repaired my Rich Yoder-built C&O H-5 hopper car. Here’s Brian’s before-and-after photo:

Brian fixed my soldering fails, unbent the ends, and re-installed the air hose connection. He used a resistance soldering tool and a whole lot of patience. Now the car looks great. Those Proto48 wheelsets look great too. Below is a photo of both cars on Brian’s workbench. He masterfully refinished both cars.

Central Auto Car

I’ve been concentrating on layout work all of 2021 but took some time in the few weeks to finish painting and building a Speedwitch Central [of Georgia] 50-foot auto car. This model released about 9-10 years ago. I got it in trade from my buddy Craig Zeni (another RPM friend!).

Central received three series of these cars in 1937, 1942 and 1944. The cars were nearly identical except for running boards, hand brakes and a few other parts. I chose to model the second delivery, series 5100-5249, which arrived from ACF in 1942. These cars had a Murphy panel roof, Murphy “W”-corner 4-5 Dreadnaught ends, Barber S-2 trucks, Youngstown-Camel doors (one six-foot and one four-foot), Universal hand brake and Apex running boards.

The Speedwitch model includes a one-piece carbody and just about all the parts needed to complete the model. Here’s the carbody casting, which required a minimum of clean up:

Below. Here’s the completed build. The used Cal Scale brake gear parts, Details West ladders, and Kadee grab irons to improve the model. I used Canopy Glue to fix the running board. The trucks are ARA Double Truss from Tahoe Model Works.

Here’s an end view. The brake gear housing is a Moloco part and the brakewheel and retainer line are from Kadee. The tack board is from National Scale Models, and the air hose and bracket is from A-Line. After the build I sandblasted the car thoroughly. Sandblasting is an absolutely essential step, which preps all the different surfaces–stainless metal, acetal, plastic, and brass and resin parts–for painting.

Above. Here’s a view of the car after paint, decals and Testors Dullcote. I used Scalecoat Oxide Red for my model, with a little red mixed into darken it a little bit. Thanks to the sandblaster there’s no trouble with paint adhesion.

Here’s a prototype view of a car in a post-1951 paint scheme, below. This is my favorite Central paint scheme but it was applied after my modeling era. I included the photo to demonstrate the paint color.

A last photo of the new car, below, this time from above.

As I studied this photo I became more interested in the track than the car. One of the things I did to the flextrack was cut the ends the web off the underside of the ties and space the ties out. That’s a pretty common thing to do these days. Another thing I did was trim the ends off of some of the ties to give them an even more irregular look. I think the effect was achieved nicely.

I hope you enjoyed the post. There’s a lot more coming. I’m way behind thanks to changing jobs, family, travel, and summer outside-time.

By the way…my son said something interesting about the Medieval churches on our trip. I raised him in the frugal Southern Baptist church, where even a chandelier or a bell tower is frowned upon. We’re supposed to spend all our money on those in need. But Jacob said, paraphrasing, “These guys worked for hundreds of years to build a lasting tribute to God. They accomplished it. Just being in these churches inspires a better understanding of the awesomeness of God. Just the awesomeness of it all.” Five or six hundred years later, these churches still help bring the awesomeness of God to man. Thankfully, the awesomeness of God is still alive in my good son.

Blessings to you and your families! – John G

No. 154: Hermitage Road Update, Feb 2021

Traditionally December and January are big modeling months as most guys are trapped inside for Winter. Not so here, as my family kept me busy and out of the attic train room until about mid-February. I also had a double-laptop meltdown, which precluded any work on the blog along with a whole lot of other stuff.

In the last 20 days I’ve been able to get a huge amount of work done on a lot of projects, and also on the Hermitage Road layout. The layout is now at the point where all the track is laid, operational, and scenicked. Fascia is painted and re-installed. All that’s left now is construction of a few buildings and finishing the backdrops.

IMG_3156

A long-term goal remains construction of a traversing table for staging instead of a traditional fiddle yard. I’ll insert a drawing as soon as I can make one. Right now the plans are all in my head.

In January and February, with what little time I had, I was able to paint, detail and weather the beautiful Seaboard VO-1000 that I leased from John Moenius. This is a Stewart-Bowser model that I upgraded with various wire parts, cab details, and a whole lot of weathering and overspray. John already had DCC and sound installed and it runs like a dream. It is my new favorite engine and I hope you like it too.

Here’s the prototype at Raleigh, North Carolina in 1949. Photo by Wiley Bryan.

SAL 1402

Here’s the model I’m using:

I’m also working on an old Proto 2000 PRR GP-7 to run during a PRR scenario. I really like the early PRR 8550 series GP-7s with the top-mounted air tanks, steam generator and antennas, so that’s what I’m building. Yes, that’s a passenger engine but I really like the look. I’m sure even the prototypes were used for local chores every once in a while.

Here’s the prototype I like:

Other engines in the queue are a Milwaukee RSC-2 and—thanks to my friend Jim Dick—an as-delivered C&NW GP-7 that I am crazy about.

Meanwhile the layout is progressing well. Here’s a view today of the industrial track ladder.

In the next few posts I’ll back up and discuss track-laying, “moving a track”—which I had to do to make more room for the coal yard—and distressing the track, which is one of my favorite sub-hobbies.

I tried a few different things when laying and ballasting track. One of the things I thought up was coloring the matte medium I use to secure ballast. Yep, I added black paint to the Elmers Glue/water/soap mixture and the results were very interesting.

IMG_3053

Finally, I’ve been putting some finishing touches on my friend Eric Reinert’s New York Central box car. You might recall that I’ve been working on this car for quite some time. I wrecked the original kit that Eric sent, and got a new one—and here’s where we are today. I salvaged the underframe and one of the ends from Eric’s original build, so it’s a Frankenstein of sorts.

Here’s a photo I took on the layout the other night. I just applied the right filter from my iPhone and this was the result. Not bad.

Much more to follow and with God’s glorious blessings may we all come out of this covid mess quickly, and with our health, and with our freedoms intact!

Next: Turnouts on Hermitage Road.

John G